We Specialize in the Calibration of:

Our Calibration Services:
This is a sampling of our capabilities. Please contact us if your equipment is not listed
*Subcontracted to an Approved Vendor
 
Ammeters Analyzers Angle Degree Blocks Angle Plates Balances
Bore Gages Calipers Caliper Master Calibrators Center Gage
Chamfer Gage Chart Recorders Clamp-On Meters Coating Thickness Gages Comptor Gages and rings
Current Probes Custom Gages Cylindrical Gages Data Loggers Depth Micrometers
Depth Vernier Durometers Durometer Test Block set Feeler Gages Force Gages
Gage Blocks Gage Setting Fixtures Groove Gages Ground Testers Hardness Testers
Heat Sealers Height Gages Hi-Pot Testers Hole Gages Indicators
Insulation Testers Intra-Mic Intra-Mic Rings Length Standards Loop Calibrator
Magna-Mike Standards Megohmeter Micro-Ohmmeter Micrometers Multimeters
Oscilloscopes Optical Comparator Oven Panel Meters Parallels
Pin Gages Pipe Thread Plugs Pipe Thread Rings Plain Plug Gages Plain Rings
Power Supplies Precision Balls Pressure Gages Processmeters Profilometers
Protractors Radius Gages Resistors Riser Blocks Roll Gages
RTD Simulator Scales Setting Fixtures Sine Bar or Plates Snap Gages
Space Block Set Spline Plug Gages Spline Ring Gages Squares Static Sensors
Steel Rules Stopwatches Straight Edges Bench Mic Surface Finish Standards
Surface Plates Tachometers Tape Measures Taper Plug Gages Taper Ring Gages
Temperature Calibrator Temperature Controllers Test Blocks Tensiometer Thermocouples
Thermometers Thickness Gages Thread Measuring Wires Thread Micrometers Thread Setting Plugs
Thread Working Plugs Thread Rings Thread Roll Gages Timers Torque Testers
Torque Wrenches V-Blocks Vacuum Gages Voltage Probes Weights*
Wire Counters Wrist Straps
Go to Top




ON SITE SERVICES:

Qual Tech Labs offers a convenient service where we calibrate your Gages at your facility, saving you time and money. All your equipment is cleaned and calibrated using the same procedures as we use in our labs.
Here is a sample list of the Gages that we calibrate on-site:

ON SITE SERVICES
*Surface plates are cleaned, measured and lapped to the grade you specify as part of our service.
 
Calipers Hardness Testers Indicators Micrometers Multimeters
Optical Comparators Ovens Pressure Gages Scales and Balances Surface Plates*
Temperature Controllers Torque Wrenches

We also replace batteries as needed.

Recall reports are sent to you a month ahead of your calibration due date along with a scheduled date. You never need to call us to schedule your calibration, let us do the work for you!

Please contact us for more information at Sales@qualtechlabs.comGo to Top




VALUE ADDED SERVICES:

Qual Tech Labs is always adding services that our customers need. We want to be your one source for all your calibration needs.

Recall Reports:
We will always notify you of gages that are coming due for calibration. We will help you with your asset management system by issuing you timely reports sorted by gage types, due dates, serial numbers or departments.

Repair Service:
We offer repair services for hand tools. Your tools are completely refurbished for the fraction of the cost to replace them.

Expedite Service:
We realize that sometimes you need to have your gages calibrated in a hurry. Call ahead to make arrangements and we can turn your gages around very quickly as needed.

Pick-Up and Delivery Service:
We offer this service to customers within a 75 mile radius for a small charge. This will prevent the possibility of damage that can occur when using a regular carrier.

Replacement Services:
We can replace out of tolerance gages for you upon request. This is especially important for gage block sets and pin sets where just one piece needs to be replaced.

Turnaround Time:
Our standard turn around time is 5 working days after receipt of your gages

Subcontract and Referral Service:
If you have a piece of equipment that is beyond our capability we can subcontract it to one of our audited approved vendors. We can also refer you to labs that have the same standards of quality that we maintain.

Go to Top

Inspection Services:

Qual Tech is now offering Inspection Services

Contract Inspection:

  • First Article
  • SPC & Process Capability Studies
  • CAD Model Based Inspection

Gage Analysis and Certification

Reverse Engineering

  • Point Cloud Date
  • Solid Surface Modeling

Please contact Bev Turner at ext. 13 for more information

Go to Top